Tuesday, May 8, 2012

Creatives Tuesdays: DIY Giant Paper Flowers Part II

Yoohoo sweethearts! We sure hope you're havin a great week! This weeks' "Double Fabulous" DIY's we want to bring a continuation to our previous wedding fad of Giant Flowers! Yay!
Remember some of you did asked us on how to DIY these gorgeous blooms.. and so many of you loved  our previous posts on DIY Giant Paper Rose & DIY Giant Paper Flowers part I. This time we're back with more new easy peasy ways to make your wedding a memorable one! For today's posting we got inspired by the giant flowers from Britney + Mark’s wedding! Thanks to Green Wedding Shoes/Britney for sharing these awesome tutorial. Britney, the lady whom made these explained she never intended on making a tutorial when creating them. Her moto was simple – "just do what works for you"  and voila we got a creative young bride!

Materials you need: 

  • Several sheets of poster board (it takes at least two full sheets of poster board per flower)
  • Large Plastic Solo Cups (1 per flower)
  • Bath poof
  • Hot glue gun and extra sticks
  • Spray Paint
  • Clear Plastic Wrap
  • Thin wall electrical conduit, ½” x 10’. Home Depot SKU# 203106
  • Halex ½” set screw connectors, Home Depot SKU# 839663
  • Raco 3 ½” round cover, Home Depot Internet SKU# 202058390
  • Wood Block or bucket filled with sand to help the flower stand up
  • Fabric to pool at the base of your stems

Preparing the bath poof:

So first, try to to use a whole poof…if it was just too much, you may cut it in half. There is a small rope that goes around the middle of the bath poof. Cut the poof in half leaving one side tied up by the rope. Keep a firm grasp on the rest of the poof. Add a generous amount of glue to the newly cut edge, then cover with a scrap of poster. Re-glue any places that is not secured. Do the same to the other half. Now you can make two flowers.
flower poof

MAKING THE FLOWER

Step One:
Lay the poster board glossy side down. (If the poster does not have a glossy side, it’s just fine.) Rip the poster towards yourself length-wise. Start by ripping pieces that are the entire length of the poster. It takes a little practice to get a good technique.
After you get 5-7 very long petals between 2-4 inches wide, move on to tearing the smaller pieces. It’s good for the petals to curl, because they will begin to flatten out over time and you don’t want a droopy flower.

Tip: Separate the petals based on size. You need several of each size, but more ofthe medium and small.
step one photo
petals in groups

Step Two:

Cut your cup in half. Then cut 1 inch tabs all the way around it. This will be your base. Hot glue your biggest petals to the OUTSIDE of the cut tabs. The weight of the petals should open the cup into a semi-flat shape.
step two

Step Three:

Continue adding petals to the INSIDE of the cup moving from largest to smallest. Be sure to fill in areas that look empty. Stop before you get to the smallest petals.



Step Four:

Glue your bath poof to the center. Once the bath poof is glued, add the smaller petals so that they curve up around it.


Step Five:

Once you are satisfied with the fullness of the flower, lightly dust the center with spray paint.
Tip: Guard the outer petals with newspaper or extra poster so they don’t get sprayed.
step five

Preparing the stem:

There is no exact technique for this one. Some have asked if PVC pipe would work, but it was said to be too flimsy. Instead, she used a thin wall electrical conduit from the electrical department at Home Depot. To make this, you may need a screw connector and a round metal outlet cover. If you are confused, print out the picture, take it to the home improvement store and they should know exactly what you need.

First, bending the conduit (stem). THIS is the difficult part: Hold the pipe up at an angle, one end resting on the ground. Slightly bend by stepping on the lowest section, move your foot up 8-10” and repeat until you have the curve you want. Be careful and don’t try to bend the conduit all at once, making numerous smaller bends works best. Once the conduit is curved, attach the Halex screw connector onto the flower end of the conduit, knock the center plug out of the Raco round cover plate and secure it to the screw connector (very easy, just sounds confusing).
diy-flower-09

Option 1: Drill a 7/8” inch hole in a large piece of wood. Insert the bent conduit stem (as seen below).
Option 2: Use buckets filled with gravel or sand to keep the flower upright.
Option 3: Simply push the stem into the ground if your event is outdoors.
Option 4: Make something up. If it works, share your wisdom with the rest of us!
diy-flower-10
diy-flower-11

Wrap the conduit in several layers of clear plastic wrap. It actually looks better if it’s a little messy.


Finally, attach the completed flower using a lot of hot glue to the 3 ½” cover plate. Ermm..You will need A LOT of hot glue. And just when you think it is secure, add more glue…just in case. You don’t want the wind taking off with the top of your flower! Now pool your fabric around the base and –Viola! You are finished!!
DIY Giant flower wedding

And a few photos from their wedding to see how they used them for their pretty outdoor ceremony –be sure to check out their entire wedding feature here!
DIY Giant flower wedding
DIY Giant flower wedding
DIY Giant flower wedding
Big thanks to Britney for putting this together, Green Wedding shoes for the collaboration and also to (once like a spark) photography for the photos!

Moderated by Songket Affairs, source Green Wedding shoes  

No comments:

Post a Comment

Thank you for your kind words. Kindly No Junk Comments or Marketing/Advertising-related not permissible on our sites unless authorised so. Thanks for your co-operation. Have a nice week loves! :)